Wolf Appliance Company Food Warmer WWD30O User Manual

INSTALLATION GUIDE  
Warming Drawers  
 
Wolf Warming Drawers  
3
wolfappliance.com/specs  
Warming Drawer Installation  
IMPORTANT NOTE: This installation must be completed  
Wolf Warming Drawer  
Model Number  
by a qualified installer or Wolf factory certified service.  
Read this entire installation guide prior to installation and  
save for the local inspector’s reference. The homeowner  
should keep this installation guide for future reference.  
Serial Number  
IMPORTANT NOTE: The warming drawer must be installed  
with a Wolf stainless steel or integrated drawer front.  
This appliance must be installed in accordance with  
National Electrical Codes, as well as all state, municipal  
and local codes. The correct voltage, frequency and  
amperage must be supplied to the appliance from a dedi-  
cated, grounded circuit which is protected by a properly  
sized circuit breaker or time delay fuse. The proper  
voltage, frequency and amperage ratings are listed on the  
product rating plate.  
Record the model and serial numbers before installing the  
warming drawer. Both numbers are listed on the product  
rating plate, located on the left front floor area of the inner  
cabinet. To access the rating plate, the drawer must be  
fully open. Refer to the illustration below.  
RATING  
PLATE  
Location of rating plate.  
 
Installation Considerations  
Installation Considerations  
4
The warming drawer must be installed with a Wolf  
stainless steel or integrated drawer front. Make sure  
you have the accessory drawer front called for in your  
installation. Specific installation instructions are  
included with the drawer front.  
TOOLS AND MATERIALS REQUIRED  
Minimum 3/4" (19) thick lumber for the solid platform  
that supports the warming drawer—must be able to  
support 200 lbs (90 kg).  
Wood screws and hardware to install the platform.  
For all installations, the warming drawer must be fully  
enclosed, top and bottom.  
Lumber for anti-tip block.  
Power saw.  
The warming drawer platform must be able to support  
200 lbs (90 kg). The platform must be a minimum of 1"  
(25) above the toe kick to allow for the warming drawer  
trim which overlaps 5/8" (16) on all four sides.  
Level.  
Drill and 1/16" bit, 1/2" bit also for integrated drawer  
front application.  
Check with local utilities for electrical codes that apply  
in your area. Local codes vary. Installation, electrical  
connections and grounding must comply with applica-  
ble codes. In the absence of local codes, the drawer  
should be installed in accordance with National Electri-  
cal Code ANSI/NFPA 70-1990 or latest edition.  
Phillips screwdriver.  
2 wood screws (provided).  
Wood cleats (optional).  
Model WWD30O is CSA approved for outdoor  
installations.  
 
Installation Considerations  
Combination Installations  
5
wolfappliance.com/specs  
Electrical Requirements  
Refer to the illustrations showing combination installations  
on pages 10–13. Also refer to installation instructions  
provided with the other Wolf products.  
The electrical supply should be located as shown in the  
illustration for your specific installation on the following  
pages. A separate circuit, servicing only this appliance is  
required.  
The warming drawer may be installed in combination  
with a Wolf built-in oven and/or microwave oven.  
Additional clearance between warming drawer and  
oven openings may be required. To allow the warming  
drawer trim and the oven trim to meet, a 7/8" (22)  
platform may be used to separate the two openings.  
This will act as the support platform for the oven and  
the anti-tip device for the warming drawer. An anti-tip  
block may be installed at the rear of the cabinet in  
place of the platform. If the warming drawer is installed  
above an oven, a 7/8" (22) platform is required to allow  
for clearance of overlaps.  
IMPORTANT NOTE: You must follow all National Electrical  
Code regulations. In addition, be aware of local codes and  
ordinances when installing your service.  
If two warming drawers are installed side by side, they can  
operate from the same electrical outlet. A 30 amp circuit  
breaker is required for this installation.  
IMPORTANT NOTE: When installed outdoors, a ground  
fault circuit interrupter (GFCI) is required to reduce the risk  
of electrical shock.  
Electrical Requirements  
The warming drawer may be installed below a Wolf  
cooktop or sealed burner rangetop. Allow enough  
room for gas and electrical connections for the  
cooktop.  
Power Supply  
Circuit Breaker  
Receptacle  
120 V AC, 50/60 Hz  
15 or 20 amp  
3-prong grounding-type  
The warming drawer may be installed next to or above  
another Wolf warming drawer.  
Model WWD30O may be installed below a Wolf  
outdoor grill.  
 
Installation Considerations  
Drawer Front Options  
6
IMPORTANT NOTE: The warming drawer must be installed  
OVERALL DIMENSIONS  
with a Wolf stainless steel or integrated drawer front.  
A
Wolf stainless steel and integrated drawer fronts allow for  
many design options, but the warming drawer itself will be  
the same for all applications.  
3
10 /8"  
9"  
(264)  
(229)  
3
/4" (19)  
When installing a Wolf warming drawer in combination  
with an L series or E series built-in oven, you may choose  
the stainless steel drawer front to match the trim and  
handle of your oven.  
7
3
29 /8" (759)  
22 /4" (578)  
B
7
OR 35 /8" (911)  
3
(19)  
1
/4"  
28 /4" (718)  
The E series 2" (51) thick drawer front with pro handle, in  
30" (762) and 36" (914) widths, is designed to be installed  
below a sealed burner rangetop or outdoor gas grill, so  
the panel aligns properly with the front of the rangetop or  
grill.  
Keep in mind, overall dimensions for the warming drawer  
remain the same, even though the drawer front may be  
wider to match a Wolf 36" (914) wide oven, sealed burner  
rangetop or outdoor grill.  
1
21 /2"  
(546)  
B
Stainless Steel Drawer Front  
L SERIES  
A
B
Tubular Handle  
7/8" (22)  
31/2" (89)  
E SERIES  
A
B
31/2" (89)  
31/2" (89)  
41/2" (114)  
Tubular Handle  
Pro Handle  
Pro Handle (2" thick)  
11/8" (29)  
11/8" (29)  
21/8" (54)  
Dimensions may vary 1/8" (3).  
Integrated Drawer Front  
CUSTOM PANEL  
W
H
D
Typical  
297/8" (759) 103/8" (264)  
3/4" (19)  
 
Installation Considerations  
7
wolfappliance.com/specs  
Installation Options  
STANDARD, RECESSED OR FLUSH INSET INSTALLATION  
Mounting holes will need to be drilled in the back of the  
drawer front panel. Holes should be drilled on site to  
ensure proper fit and gaps are achieved. A drilling  
template is provide with the integrated drawer front.  
The warming drawer with E series drawer front can be  
installed in a standard, recessed or flush inset application.  
For a standard installation, the drawer collar and front  
panel sit proud of the cabinet face frame. A recessed  
installation requires the cabinetry be recessed by 3/16" (5)  
so the collar is flush with the cabinet face frame but the  
drawer front will sit proud. A flush inset installation  
requires the drawer collar and front panel be recessed to  
be flush with surrounding cabinetry. Refer to illustrations  
on the following pages for minimum cabinet dimensions  
for your specific installation.  
IMPORTANT NOTE: Be sure to finish the inside lip of the  
opening and the front face of the platform and cleats.  
These areas may be visible when the drawer is open.  
IMPORTANT NOTE: Be aware of the location of the  
mounting holes on the warming drawer frame to make  
sure screws used to attach the cleats do not interfere with  
screw holes for mounting the warming drawer.  
INSTALL RECESSED CLEATS AND PLATFORM  
For a recessed or flush inset application, you will need to  
install a recessed platform and cleats into the opening.  
Proper recess of the platform and cleats is critical to the  
function and esthetics of the warming drawer installation.  
The depth of the platform may increase with the cabinet  
depth. Be sure to rigidly mount the platform so that it  
can support a minimum of 200 lbs (90 kg). Refer to the  
illustrations below.  
TOP CLEAT  
TOP CLEAT  
PLATFORM  
PLATFORM  
SIDE CLEAT  
SIDE CLEAT  
CLEATS AND PLATFORM  
RECESSED 3/16" (5)  
CLEATS AND PLATFORM  
RECESSED 3/16" (5)  
PLUS THICKNESS  
CABINETRY  
OPENING  
CABINETRY  
OF DECORATIVE PANEL OPENING  
Recessed application.  
Flush inset application.  
 
Warming Drawer Specifications  
8
Standard Installation  
L SERIES, E SERIES OR INTEGRATED DRAWER FRONT  
DIMENSION  
ANTI-TIP BLOCK  
WILL VARY*  
1
3
9 /8" (232)  
10 /8"  
5
28 /8" (727)  
OPENING HEIGHT  
(264)  
OPENING WIDTH  
E
PLATFORM  
1
36" (914)  
FLOOR TO  
23 /2"  
(597)  
24"(610) min  
CABINET DEPTH  
COUNTERTOP  
TYPICAL  
SIDE VIEW  
*Dimension must accommodate height of anti-tip block and drawer face overlap.  
FRONT VIEW  
NOTE: Location of electrical supply within opening may require additional cabinet depth. Dashed line represents profile of unit.  
 
Warming Drawer Specifications  
9
wolfappliance.com/specs  
Flush Inset Installation  
E SERIES OR INTEGRATED DRAWER FRONT  
TOP VIEW  
24 (610) min  
FLUSH INSET  
DEPTH  
1" (25)  
SIDE CLEATS  
DIMENSION  
ANTI-TIP BLOCK  
WILL VARY*  
7
/8" (22) TOP AND SIDE CLEATS  
7
10 /8" (276)  
1
9 /8" (232)  
5
28 /8" (727)  
FLUSH INSET  
HEIGHT  
OPENING HEIGHT  
OPENING WIDTH  
E
7
/8" (22) PLATFORM  
E
1
3
36" (914)  
FLOOR TO  
23 /2"  
30 /8"(772)  
(597)  
FLUSH INSET WIDTH  
COUNTERTOP  
TYPICAL  
SIDE VIEW  
FRONT VIEW  
*Dimension must accommodate height of anti-tip block and drawer face overlap.  
1
NOTE: Dimensions provided allow for /4" (6) reveal for proper air flow. Location of electrical supply within opening may require additional  
cabinet depth. Dashed line represents profile of unit.  
 
Warming Drawer Specifications  
10  
Standard Tower Installation  
INSTALLATION WITH MICROWAVE AND BUILT-IN OVEN  
1"(25) min  
L SERIES  
MICROWAVE  
OPENING  
1
1 /2"(38) min  
E SERIES  
E
3
1
27 /16"  
(691)  
28 /2" (724)  
24"(610) min  
OPENING DEPTH  
OVEN OPENING WIDTH  
4"  
(102)  
PLATFORM*  
5"  
E
E
E
(127)  
1
3
9 /8" (232)  
/4" (19)  
min  
5
28 /8" (727)  
WARMING DRAWER  
OPENING WIDTH  
SIDE VIEW  
FRONT VIEW  
*Platform must support 250 lbs (113 kg).  
NOTE: Location of electrical supply within oven opening may require additional cabinet depth.  
 
Warming Drawer Specifications  
11  
wolfappliance.com/specs  
Flush Inset Tower Installation  
INSTALLATION WITH STANDARD MICROWAVE AND E SERIES OVEN  
TOP VIEW  
3
24 /4"  
(629) min  
FLUSH  
INSET  
1" (25)  
DEPTH  
SIDE CLEATS  
3
30 /8" (772) min  
FLUSH INSET WIDTH  
11  
/16" (17) TOP CLEAT  
1
1
17" (432)  
OPENING  
HEIGHT  
18 /2" (470)  
27 /2" (699)  
FLUSH INSET  
HEIGHT  
STANDARD MICROWAVE  
OPENING WIDTH  
11  
E
1
/16" (43) PLATFORM  
3
1
1
27 /16"  
28 /8"  
28 /2" (724)  
(691)  
OPENING  
HEIGHT  
(714) min  
FLUSH INSET  
HEIGHT  
E SERIES OVEN  
OPENING WIDTH  
1" (25)  
SIDE CLEATS  
4"  
(102)  
9
/16" (14)  
5"  
E
E
PLATFORM*  
(127)  
5
10 /8"  
E
5
1
28 /8" (727)  
9 /8" (232)  
(270)  
FLUSH INSET  
HEIGHT  
WARMING DRAWER  
OPENING WIDTH  
OPENING HEIGHT  
1" (25) PLATFORM  
SIDE VIEW  
*Platform must support 250 lbs (113 kg).  
FRONT VIEW  
NOTE: Location of electrical supply within oven opening may require additional cabinet depth. Dashed line represents profile of unit.  
 
Warming Drawer Specifications  
12  
Flush Inset Tower Installation  
INSTALLATION WITH CONVECTION MICROWAVE AND E SERIES OVEN  
TOP VIEW  
3
24 /4"  
(629) min  
FLUSH  
INSET  
1" (25)  
DEPTH  
SIDE CLEATS  
3
30 /8" (772) min  
FLUSH INSET WIDTH  
1
/2" (13) TOP CLEAT  
7
1
1
18 /8" (479)  
20 /8"  
27 /2" (699)  
(511)  
FLUSH INSET  
HEIGHT  
OPENING  
HEIGHT  
CONVECTION MICROWAVE  
OPENING WIDTH  
5
E
1 /8" (41) PLATFORM  
3
1
1
27 /16"  
28 /8"  
28 /2" (724)  
(691)  
OPENING  
HEIGHT  
(714) min  
FLUSH INSET  
HEIGHT  
E SERIES OVEN  
OPENING WIDTH  
1" (25)  
SIDE CLEATS  
4"  
(102)  
9
/16" (14)  
5"  
E
E
E
PLATFORM*  
(127)  
5
10 /8"  
5
1
28 /8" (727)  
9 /8" (232)  
(270)  
FLUSH INSET  
HEIGHT  
WARMING DRAWER  
OPENING WIDTH  
OPENING HEIGHT  
1" (25) PLATFORM  
SIDE VIEW  
*Platform must support 250 lbs (113 kg).  
FRONT VIEW  
NOTE: Location of electrical supply within oven opening may require additional cabinet depth. Dashed line represents profile of unit.  
 
Warming Drawer Specifications  
13  
wolfappliance.com/specs  
Flush Inset Tower Installation  
INSTALLATION WITH DRAWER MICROWAVE AND E SERIES OVEN  
TOP VIEW  
1
3
1 /4" (32)  
24 /4"  
FOR MICROWAVE (629) min  
1" (25) FOR OVEN  
AND WARMING  
DRAWER  
FLUSH  
INSET  
DEPTH  
SIDE CLEATS  
3
30 /8" (772) min  
FLUSH INSET WIDTH  
7
/8"(22) TOP CLEAT  
3
1
1
27 /16"  
28 /8"  
28 /2" (724)  
(691)  
OPENING  
HEIGHT  
(714) min  
FLUSH INSET  
HEIGHT  
E SERIES OVEN  
OPENING WIDTH  
1" (25)  
SIDE CLEATS  
4"  
(102)  
9
/16" (14)  
5"  
E
E
PLATFORM*  
(127)  
E
3
3
1
14 /4" (375)  
15 /8"  
28 /2" (724)  
(391)  
FLUSH INSET  
HEIGHT  
OPENING  
HEIGHT  
DRAWER MICROWAVE  
OPENING WIDTH  
5
/8" (16) PLATFORM  
5
10 /8"  
E
5
1
28 /8" (727)  
9 /8" (232)  
(270)  
FLUSH INSET  
HEIGHT  
WARMING DRAWER  
OPENING WIDTH  
OPENING HEIGHT  
1" (25) PLATFORM  
SIDE VIEW  
*Platform must support 250 lbs (113 kg.  
FRONT VIEW  
NOTE: Location of electrical supply within oven opening may require additional cabinet depth. Dashed line represents profile of unit.  
 
Warming Drawer Installation  
14  
Anti-Tip Block  
Install the Warming Drawer  
INSTALL ANTI-TIP BLOCKING  
Unpack the warming drawer on a flat surface. Remove all  
packaging materials from inside the warming drawer. Do  
not discard the package containing the two wood screws  
needed for installation.  
Install an anti-tip block against the rear cabinet wall. When  
the warming drawer is installed below a built-in oven, you  
may use a 7/8" (22) thick platform to allow the warming  
drawer trim and the oven trim to meet. The platform will  
act as an anti-tip device for the warming drawer.  
Turn power off to the electrical outlet.  
Slide the left corner of the warming drawer into the  
opening. If the electrical outlet is installed inside the  
opening, plug the power cord into the outlet. The excess  
cord should be coiled behind or beside the unit. If the  
outlet is located in an adjacent cabinet, thread the power  
cord through the hole in the cabinet wall. Push the drawer  
back into the opening until the trim meets the cabinet  
front. Make sure the power cord does not get trapped  
under the warming drawer.  
An anti-tip block or platform must be installed to  
prevent the warming drawer from tipping forward while  
opened when loaded. Failure to do so could result in  
personal injury and damage to the cabinet.  
IMPORTANT NOTE: Do not lift up on the handle to push  
the drawer into place.  
Open the warming drawer to its full extension. Drill pilot  
holes in each side hole, located toward the front on each  
side of the warming drawer. Install the wood screws  
provided with the unit. Refer to the illustration below.  
Turn power back on to the electrical outlet.  
LOCATION OF  
SIDE HOLE  
Location of side hole.  
 
Service Information  
Troubleshooting  
15  
wolfappliance.com/specs  
Service Information  
IMPORTANT NOTE: If the warming drawer does not  
If service is necessary, maintain the quality built into your  
warming drawer by contacting Wolf factory certified  
service.  
operate properly, follow these troubleshooting steps:  
Verify that electrical power is being supplied to the  
warming drawer.  
For the name and number of Wolf factory certified service  
nearest you, check the contact & support section of our  
website, wolfappliance.com or call Wolf customer service  
at 800-222-7820.  
Check electrical connections to ensure that the instal-  
lation has been completed correctly.  
Refer to the troubleshooting guide in the Wolf warming  
drawers use & care guide.  
When calling for service, you will need the model and  
serial numbers of the warming drawer. Both numbers are  
listed on the product rating plate, located on the left front  
floor area of the inner cabinet. To access the rating plate,  
the drawer must be fully open. Refer to the illustration  
below.  
If the warming drawer still does not operate properly,  
contact Wolf factory certified service. Do not attempt  
to repair the warming drawer yourself. Wolf is not  
responsible for service required to correct a faulty  
installation.  
RATING  
PLATE  
Location of rating plate.  
The information and images in this guide are the copyright property of Wolf Appliance, Inc. Neither this guide nor any information or images contained herein  
may be copied or used in whole or in part without the express written permission of Wolf Appliance, Inc. ©Wolf Appliance, Inc. all rights reserved.  
Wolf, Wolf & Design, Wolf Gourmet, W & Design and the color red as applied to knobs are registered trademarks and service marks of Wolf Appliance, Inc.  
Sub-Zero, Sub-Zero & Design, Dual Refrigeration, Constant Care and The Living Kitchen are registered trademarks and service marks of Sub-Zero, Inc.  
(collectively, theCompany Marks.) All other trademarks or registered trademarks are property of their respective owners in the United States and other countries.  
 
WOLF APPLIANCE, INC. P. O. BOX 44848 MADISON, WI 53744 WOLFAPPLIANCE.COM 800.222.7820  
816978 REV-A  
1/2011  
 

Whirlpool Oven RS610PXGN3 User Manual
Whirlpool Ventilation Hood 29 718 User Manual
Whirlpool Washer Dryer LA5OOOXP User Manual
Woods Equipment TV Mount BH7500 User Manual
Xerox Printer 3315 DN User Manual
Yamaha CD Player CDC 745 User Manual
Yamaha CD Player EMX100RDS User Manual
Yamaha Electronic Keyboard DGX 520 User Manual
Zanussi Washer ZWF 1415W User Manual
Zebra Technologies Printer 105SL Plus User Manual