111
WELLS MANUFACTURING COMPANY
2 ERIK CIRCLE, P. O. Box 280
Verdi, NV 89439
Customer Service (775) 345-0444 Ext.502
fax: (775) 345-0569
OPERATION
MANUAL
for
BUILT-IN
ELECTRIC
GRIDDLES
includes:
INSTALLATION
USE and CARE
IMPORTANT: DO NOT DISCARD THIS MANUAL
This manual is considered to be part of the GRIDDLE and is to be given to the OWNER
or MANAGER of the restaurant, or to the person responsible for TRAINING OPERATORS
of the GRIDDLE. Additional manuals are available from your WELLS DEALER .
THIS MANUAL MUST BE READ AND UNDERSTOOD BY ALL PERSONS USING OR
INSTALLING THIS GRIDDLE. Contact your WELLS DEALER if you have any questions
concerning installation, operation or maintenance of this equipment.
P/N 303340 Rev.(-)
M101 110100 cps
TABLE OF CONTENTS
Warranty
Inside Cover
Features and Operating Controls
Safety Procedures
Warmer Precautions & General Information
Installation Instructions
2
3
3
4
6
Operation
Preventative Maintenance
Standard Griddle Cleaning Instructions
Chrome Plated Griddle Cleaning Instructions
Parts & Service
7
9
11
SHIPPING DAMAGE CLAIM PROCEDURE
NOTE: For your protection, please note that equipment in this shipment was carefully inspected
and packaged by skilled personnel before leaving the factory. Upon acceptance of this shipment,
the transportation company assumes full responsibility for its safe delivery.
IF SHIPMENT ARRIVES DAMAGED:
1. VISIBLE LOSS OR DAMAGE: Be certain that any visible loss or damage is noted on
the freight bill or express receipt, and that the note of loss or damage is signed by the
delivery person.
2. FILE CLAIM FOR DAMAGE IMMEDIATELY: Regardless of the extent of the damage.
3. CONCEALED LOSS OR DAMAGE: if damage is unnoticed until the merchandise is
unpacked, notify the transportation company or carrier immediately, and file
“CONCEALED DAMAGE” claim with them. This should be done within fifteen(15) days
from the date the delivery was made to you. Be sure to retain the container for inspection.
Wells Manufacturing cannot assume liability for damage or loss incurred in transit. We will,
however, at your request, supply you with the necessary documents to support your claim.
1
FEATURES and OPERATING CONTROLS
A.
THERMOSTAT
On THERMOSTATICALLY CONTROLLED griddles, power is
applied to the griddle heating element according to the control
knob position and the actual temperature at the temperature
sensing thermobulb.
TEMPERATURE
CONTROL
KNOB
The temperature of each section of the griddle is
individually controllable to allow preparation of different
products, or to allow the griddle to be used for both product
preparation and temporary holding of prepared product.
INDICATOR
LIGHT
The dial position is an indication of the temperature
setting. Actual griddle surface temperature will vary,
depending upon type and initial temperature of product ,
and other variables.
B.
GREASE TROUGH
SPLASH
GUARD
Extra wide trough with radiused corners makes cleaning
easier. Trough slopes to large waste hole in center,
which empties into the removable grease drawer.
GREASE
TROUGH
C.
GREASE DRAWER
Large-capacity drawer is removable from the front for
easy cleaning. Special “reminder” hole in center of
drawer indicates when drawer is full.
D.
REMOVABLE SPLASH GUARD
Stainless steel splash guard simplifies griddle
maintenance and keeps grease from splattering onto
adjacent walls and equipment.
GREASE
DRAWER
E.
WELLSLOKS
Built-in griddles are equipped with WELLSLOKS, uniquely
designed turnout tabs which help secure the griddle to the
countertop. (See the Installation Instructions suppliedwith the
griddle for details.)
WELLSLOKS
2
SAFETY PROCEDURES
Knowledge of proper procedures is essential to the safe operation of electrically energized
equipment. In accordance with generally accepted product safety labeling guidelines for
potential hazards, the following signal words and symbols are used throughout this manual.
DANGER - Danger is used to indicate the presence of a hazard which will
cause severe personal injury, death, or substantial property damage in the
event the statement is ignored.
WARNING - Warning is used to indicate the presence of a hazard which can cause
personal injury and possibly death, or major property damage, in the event the state-
ment is ignored.
CAUTION - Caution is used to indicate the presence of a hazard which will or can
cause minor personal injury, or property damage in the event the statement is ignored.
CAUTION - Used to indicate the presence of an electrical hazard which will or can
cause personal injury, or property damage in the event the statement is ignored.
NOTE - Note is used to notify personnel of installation, operation or maintenance information
which is important, but not hazard related.
GRIDDLE PRECAUTIONS AND GENERAL INFORMATION
1.
2.
Griddles are intended for use tocook food products for human consumption. No other use is
recommended or authorized by the manufacturer or itsagents.
Griddles are intended for use in commercial establishments, where all operators are familiar with
the appliance use, limitations and associated hazards. Operating instructions and warnings must
be read and understood by all operators and users.
3.
4.
5.
Do not splash or pour water onto controls, control panels or wiring.
Unplug griddle or disconnect from electrical power before performing any service or maintenance.
Any parts replacement, maintenance procedure or servicing procedure requiring the use of tools
must be performed by an Authorized Service Agency.
6.
7.
8.
Any troubleshooting guides, component views, parts lists or installation guides provided with this
equipment are intended for the use of qualified technical personnel only.
Except where otherwise noted, this piece of equipment is made in the USA and has American sizes on
hardware.
This manual should be considered a permanant part of this appliance. This manual and all
supplied instructions, diagrams, schematics, parts break downs, notices and labels must remain
with the appliance if it is sold or moved to another location.
3
INSTALLATION INSTRUCTIONS
A.
UNPACKING AND INSPECTION
1. Carefully remove the GRIDDLE from the carton. Remove all protective plastic film, packaging
materials and accessories from the GRIDDLE before connecting electrical power or otherwise
performing any installation procedures.
NOTE: DO NOT discard the CARTON and other PACKAGING MATERIAL until you have
inspected the warmer for hidden damage and tested it for PROPER OPERATION.
Refer to SHIPPING DAMAGE CLAIM PROCEDURE on page 1 of this manual.
2. Read all instructions in this manual carefully before starting installation of this griddle. READ AND
UNDERSTAND ALL LABELS AND DIAGRAMS ATTACHED TO THE GRIDDLE.
3. Carefully account for all components and accessories before discarding packing materials.
Store the accessories in a convenient place for later use:
B.
INSTALLATION NOTES
1. Installation and start up of built-in griddles MUST be performed by an authorized installation company.
2. It is the RESPONSIBILITY OF THE INSTALLER to verify that this griddle installation is in
compliance with the specifications listed in this manual and on the specification sheet provided.
3. It is the RESPONSIBILITY OF THE INSTALLER to check with the AUTHORITY HAVING JURISDICTION,
in order to verify that this griddle installation is in compliance with local code requirements.
C. BUILT-IN GRIDDLES
1. This is a GENERAL GUIDE. For specific cutout dimensions and other installation details, refer to
the Installation Instructions supplied with the griddle.
2. Cutouts
a.
Cutout dimensions for griddle and control panels are listed on the Installation Instructions
provided with the griddle.
b.
c.
Verify griddle and control panel dimensions before making cutout.
Griddles must be installed in all-metal counters only.
3. Installation
a.
b.
c.
Verify that provided sealants are applied to the
underside of the top flange prior to setting the
unit into the cutout.
After installation, verify that the tabs on the
Wellsloks are turned out to lock the griddle into
the counter.
Apply a thin bead of food-grade silicone sealant
around the flange to seal it to the counter.
NOTE: Damage caused by leaks due to improper
installation is NOT covered by warranty.
4
D.
ELECTRICAL HOOK-UP
Electrical installation must be performed by a licensed electrician in compliance
with all local ordinances and code requirements.
IMPORTANT:
1. Refer to the nameplate. Verify the electrical service power. Voltage and phase must
match the nameplate specifications. Connecting the griddle to the wrong voltage can severely
damage the unit or cause noticeably decreased performance.
IMPORTANT: Damage due to being connected to the wrong voltage is NOT covered by warranty.
2. Use copper wire suitable for at least 90ºC for supply connections.
3. Griddles are factory wired three-phase (3ø). For single-phase (1ø) wiring, refer to the wiring
diagram attached to the griddle.
CAUTION: Electrical Shock Hazard
This griddle must be electrically grounded.
G
Connect the terminal marked “GND” or “
” to a suitable building ground.
4. This griddle is not fused. Protect the circuit with properly sized fuses or circuit breaker.
5. An electrical disconnect must be installed readily accessible to the operator of the griddle.
RECOMMENDED GRILLING TIMES AND TEMPERATURES
NOTE: The times and temperatures in this chart are suggestions only. Your own experience
with your own menu items will be your best guide to achieving the best food product.
PRODUCT
TEMPERATURE ºF
TIME
Sausage, link and patty
Bacon
350º
350º
350º
375º
375º
400º
400º
400º
350º
350º
375º
325º
3 minutes
2 - 3 minutes
2 - 3 minutes
3 - 4 minutes
2 minutes
Canadian Bacon
Ham Steaks
Broiled Ham
Beef Tenderloin
Minute Steaks
Club Steak, 1” thick
Hamburgers
3 - 4 minutes
3 - 4 minutes
3 - 5 minutes
3 - 4 minutes
3 - 4 minutes
3 - 4 minutes
2 - 3 minutes
Cheeseburgers
Melted Cheese Sandwich
Hot Dogs
5
OPERATING INSTRUCTIONS
A.
PREPARING THE GRIDDLE SURFACE
1. SEASONING STANDARD GRIDDLES
As manufactured, the steel surface of your Wells griddle has microscopic pores. It is important to
fill these pores with oil in order to provide a hard, non-stick cooking surface.
a.
b.
c.
d.
e.
Preheat the griddle surface to 375ºF (191ºC).
Spread a light film of cooking oil over the entire griddle surface
Allow the oil film to cook in for approximately 2 minutes, or until it smokes.
Wipe the griddle surface with a clean damp cloth until all oil is removed.
For new griddles, repeat this procedure 2-3 times until the griddle has a slick, clean surface.
2. CHROME PLATED GRIDDLES
Because the microscopic pores in the griddle surface are filled by the chrome plating, no seasoning
of the griddle surface is required.
a.
Thoroughly clean the griddle surface using a soft clean cloth and a small amount of mild
detergent.
b.
c.
Rinse and dry thoroughly after cleaning.
The griddle is now ready to use.
IMPORTANT: SCRATCHES WILL DAMAGE THE GRIDDLE SURFACE!
DO NOT use anything on this griddle that could scratch the surface.
DO NOT clean chrome surface with griddle bricks, pumice stone or abrasive cleansers.
B.
USING THE GRIDDLE
CAUTION: Hot surfaces
Exposed surfaces can be very hot and may cause severe burns on contact.
1. Check the chart on page 6 for recommended cooking temperatures. Turn the temperature control
knob to the desired temperature. The indicator light will glow while the griddle is heating. When the
indicator light first goes out, the griddle is ready to use.
NOTE: Separate sections of the griddle may be set to different temperatures. This will allow a
variety of products to be prepared at the same time, and will allow prepared product to be held
at serving temperature after cooking. For best results, different temperatures should be set from
(Heat will migrate over the entire
griddle surface. Setting one section low, adjacent to a section set high, may overwork components
in the “high” section as the thermostat tries to compensate for heat lost to the “low” section.)
coolest to hottest sequentially across the width of the griddle.
2. For standard griddles, keep the griddle surface clean and well oiled during use. Scrape cooking
waste into the grease trough frequently during use. Occasionally brush or spray a light coat of
cooking oil on the griddle surface in order to maintain the non-stick surface.
3. For chrome plated griddles, scrape cooking waste into the grease trough after preparing each order.
DO NOT bang or tap pots, pans, spatulas or other metal utensils on the griddle surface as this may
damage the chrome plating.
6
PM 111.1
PREVENTATIVE MAINTENANCE CARD
STANDARD ELECTRIC GRIDDLE
CLEANING INSTRUCTIONS
PREPARATIONS:
Set temperature control to 220ºF. Allow the griddle temperature to drop to
220ºF before proceeding.
FREQUENCY:
TOOLS:
Daily
Griddle Brick or Pumice Stone
Fiber Brush
Plastic Scouring Pad, Plastic Scraper
Mild Detergent, Non-Abrasive Cleanser
Clean Soft Cloth / Sponge
Food Grade Silicone Sealant
1. Pour a small amount of water on the griddle surface and let it "sizzle".
2. Clean the griddle surface:
a.
For standard griddles, use a pumice stone or griddle brick to scrape food waste.
Clean the griddle surface down to bright metal. Wipe off any remaining
powder residue.
b.
For grooved-surface griddles, use the supplied contoured scraper to scrape food
waste. Clean the griddle surface down to bright metal.
IMPORTANT: NEVER USE STEEL WOOL TO CLEAN THE GRIDDLE SURFACE!
DO NOT use detergent or oven cleaner to clean the griddle surface.
3. Use a soft-bristled fiber brush in a circular motion to remove any remaining food particles.
4. Turn temperature control to OFF. Allow the griddle surface to cool, then wipe the surface
with a clean cloth. Dry the griddle surface thoroughly.
IMPORTANT: SEASON THE COOKING SURFACE AFTER EACH CLEANING.
5. At least once each day, the grease trough must be thoroughly cleaned. Using a scraper,
remove all grease and food waste from the grease trough by pushing it down the waste
hole and into the grease drawer.
6. After scraping all cooking waste from grease trough into the grease drawer, take the
grease drawer to kitchen cleaning area and properly dispose of all waste.
a.
b.
Clean drawer with hot water and a mild detergent.
Dry drawer thoroughly and reinstall in griddle.
7. Clean the splash guard in the sink with warm water and mild detergent, or in the dish
washer. Rinse thoroughly and reinstall.
IMPORTANT: DO NOT splash or pour water onto control panel or wiring.
8. Check flange-to-counter seal. Reseal with food-gradesilicone sealant if necessary
Procedure is complete.
7
PM 111.1
8
PM 111.2
PREVENTATIVE MAINTENANCE CARD
CHROME PLATED ELECTRIC GRIDDLE
CLEANING INSTRUCTIONS
PREPARATIONS:
Set temperature control to 225ºF. Allow the griddle temperature to drop to
225ºF before proceeding.
FREQUENCY:
TOOLS:
Daily
4” Razor-Style Scraper
Mild Detergent, Non-Abrasive Cleanser
Clean Soft Cloth / Sponge
Food Grade Silicone Sealant
1. Pour a small amount of water on the griddle surface and let it "sizzle".
2. Use a 4” razor-style scraper to clean the remaining food particles from the griddle surface
IMPORTANT: NEVER USE GRIDDLE BRICKS, PUMICE STONES OR STEEL
WOOLTO CLEAN THE GRIDDLE SURFACE!
DO NOT use detergent or oven cleaner to clean griddle surface.
IMPORTANT: NEVER BANG OR TAP METAL IMPLEMENTS, SPATULAS, POTS,
PANS, OR SCRAPERS ON THE GRIDDLE SURFACE!
3. Use a soft-bristled fiber brush in a circular motion to remove any remaining food particles.
4. Turn temperature control to OFF. Allow the griddle surface to cool, then wipe the surface
with a clean cloth. Dry the griddle surface thoroughly.
5. At least once each day, the grease trough must be thoroughly cleaned. Using a scraper,
remove all grease and food waste from the grease trough by pushing it down the waste
hole and into the grease drawer.
6. After scraping all cooking waste from grease trough into the grease drawer, take the
grease drawer to kitchen cleaning area and properly dispose of all waste.
a.
b.
Clean drawer with hot water and a mild detergent.
Dry drawer thoroughly and reinstall in griddle.
7. Clean the splash guard in the sink with warm water and mild detergent, or in the dish
washer. Rinse thoroughly and reinstall.
IMPORTANT: DO NOT splash or pour water onto control panel or wiring.
8. Check flange-to-counter seal. Reseal with food-gradesilicone sealant if necessary.
Procedure is complete.
9
PM 101.2
10
PARTS & SERVICE
IMPORTANT: Use only factory authorized service parts and replacement filters.
For factory authorized service, or to order factory authorized replacement parts, contact your
WELLSAUTHORIZED SERVICEAGENCY, or call:
Wells Manufacturing Company
2 Erik Circle, P. O. Box 280
Verdi, NV 89439
phone: (775) 345-0444 ask for:
Customer Service
fax:
(800) 356-5142
Service Parts Department
fax: (888) 492-2783
Service Parts Department can supply you with the name / telephone number of the WELLS
AUTHORIZED SERVICEAGENCY nearest you.
ACCESSORIES
PART#
SPLASHGUARD, FITS G-136
SPLASHGUARD, FITS G-156
SPLASHGUARD, FITS G-196
SPLASHGUARD, FITS G-236
SPLASHGUARD, FITS G-246
SPLASHGUARD, FITS G-606
SCRAPER, GROOVED GRIDDLE
20632
20633
20634
20635
20636
20637
20651
CUSTOMER SERVICE DATA
please have this information available if calling for service
RESTAURANT _____________________________ LOCATION _______________
INSTALLATION DATE ________________________TECHNICIAN _____________
SERVICE COMPANY __________________________________________________
ADDRESS ___________________________ STATE ______ ZIP__________
TELEPHONE NUMBER (_____)_____-_________
EQUIPMENT MODEL NO. ______________________________________________
EQUIPMENT SERIAL NO. ______________________________________________
VOLTAGE: (check one)
208V
240V
480V
11
WELLS MANUFACTURING COMPANY
2 ERIK CIRCLE, P. O. Box 280
Verdi, NV 89439
Customer Service (775) 345-0444 Ext. 502
fax: (775) 345-0569
|